Common Concours Part Numbers

Common Concours Part Numbers
Generic and OEM

Accessories: both Factory and Aftermarket
Aftermarket Clothing
Givi Replacement Keys

DISCLAIMER: THESE PN#s HAVE BEEN CHECKED FOR ACCURACY, BUT AS ALWAYS, MISTAKES MAY OCCUR, VERIFY THAT THE PART MATCHES YOUR OLD PART BEFORE INSTALLATION!

NEWS FLASH! For any OEM parts not listed here try BuyKawasaki.com

If you have any part numbers you would like to contribute, email Bryan Moody link at bottom of page

Bryan's Tech Page
David Morrow's Tech Page

Ron Ayers Motorsports-Genuine Kawasaki Parts for approximately 70% of list price

SYSTEM	DESCRIPTION	GENERIC	KAWASAKI
	SERVICE MANUAL Have this in hand BEFORE starting work!	None Available	99924-1065-9
brakes	ring, brake piston seal (front & rear)		43049-002
brakes	packing, brake piston (front & rear)		43049-1028
brakes	front master cylinder cover also used on clutch side		43026-1052
brakes	front master cylinder cover diaphragm also used on clutch side		43028-1058
cables	cable, speedometer drive	Dennis Kirk (Motion Pro) #C9059	54001-1119
cables	cable, throttle closing		54012-1303
cables	cable, throttle opening		54012-1302
chassis	bag antler (bag stay), LH		35011-1300
chassis	bag antler (bag stay), RH		35011-1301
chassis	bag keys "A"		27008-1127-AA
chassis	bag keys "B"		27008-1127-BB
chassis	bearing, steering head LOWER		92116-1009
chassis	bearing, steering head UPPER (25mm bore x 47mm OD x 15mm wide)	Parts Plus: SSK902 (Rick Nolan) BCA (Federal Mogul): 32005 (Rick Hall) Bower: 32005 get at any bearing supply (see note #1)	92116-1056
chassis	bearing, front wheel 86-93 (15mm bore x 42mm OD x 13mm wide)	6302 double seals, get at any bearing supply (see note #1)	601B6302U
chassis	bearing, front wheel 94-up (17mm bore x 40mm OD x 12mm wide)	6203 double seals, get at any bearing supply (see note #1)	601B6304UU
chassis	bearing, rear wheel (all years) (20mm bore x 52mm OD x 15mm wide)	6304 double seals, get at any bearing supply (see note #1)	601B6304ZZ
chassis	bearing, swingarm tapered roller bearing single row (20mm bore x 42mm OD x 15mm wide)	Federal Mogul: 32004 NSK: 32004 Bower: 32004 get at any bearing supply (see note #1)	92116-1061
chassis	collar, metal collar that goes under mounting screws on belly pan		92027-1935
chassis	flap, side cowling LH (fairing extender) WINTER		35019-1193
chassis	flap, side cowling RH (fairing extender) WINTER		35019-1194
chassis	trim, inner cowling quantity 2 use w/winter side cowling (these are rubber seals that fit between the side cowling and the fairing).		53044-1184
chassis	fairing extender KIT Includes both above cowlings and inner trim Less expensive than buying parts separately		K99996-1103
chassis	footpeg bracket, LH		34003-1259
chassis	footpeg bracket, RH		34003-1260
chassis	footpeg feelers (bank sensor)		92043-1219
chassis	footpeg, LH (metal only)		34028-1198
chassis	footpeg, RH (metal only)		34028-1199
chassis	fork bushings		44065-1085
chassis	fork bushing, inner		44065-1081
chassis	fork circlips (fit above seals)		92033-1036
chassis	fork seals, inner		92049-1273
chassis	fork seals, outer (dust cover)		92093-1232
chassis	mirror, LH	Replacement glass only, convex (cut to fit) G.M. PN# 15635578 (James Freeman)	56001-1333
chassis	mirror, RH	Replacement glass only, convex (cut to fit) G.M. PN# 15635578 (James Freeman)	56001-1334
chassis	plug, (plastic) for allen head bolts		92066-1216
chassis	reflector, reflex (for saddlebag)		28012-1077
chassis	shift lever pedal assy.		13242-1213
chassis	shift lever rubber cover		92075-1175
chassis	shock-all years	Progressive Suspension: 420-1016	45014-1340
chassis	speedometer drive assy		41078-1061
chassis	spring, fork-all years	Progressive Suspension: 11-1102	44026-1340 (86-93)
chassis	rear suspension link seal		92049-1109
chassis	trim, inner cowling quantity 2 use w/winter side cowling		53044-1184
chassis	valve stem, tire 90 degree reccomended on rear wheel for gauge access		16126-1191
chassis	valve stem, tire straight		16126-1136
electrical	alternator rectifier		13091-1329
electrical	battery 12V18AH 7 1/8" L x 3 5/8" W x 6 7/16" H	Exide: 18LA (Will Brown) Hawker Odessey: PC680 (Mark Cipriano) Interstate: 18LA (Will Brown) Sears Diehard: 44071 (Kevin Arnold) Super Crank: 18LA (Kevin Arnold) Westco: 12V20L (Mark Cipriano) Yuasa: YB18L-A Sealed Battery: Yuasa: YTX20L-BS	26012-1130
electrical	brush, alternator		21039-1052
electrical	brush, starter motor		21039-1053
electrical	junction box		59416-1060
electrical	junction box relays SPDT, 5 amp DC contact rating 12 VDC coil	Aromat: JS1E-12V NTE: R46-5D3-12 (NTE is a nationally distributed replacement parts brand, try your local electronic part house or http://www.mouser.com ) thanks to Rick Nolan for the NTE number
electrical	key blank	Ilco: KA14 Taylor: X103	27008-1103
electrical	lamp, headlamp bulb, 100/80	NAPA: BP1210/H4 ($10.99)	92069-1002
electrical	headlamp socket	NAPA LS 6235 (bakelite) (Jim Dickinson) or 1984 Honda Accord get from junkyard, will not melt when used with high wattage bulbs SEE NOTE 2 BELOW
electrical	lamp, taillamp 12V 27/8W	1157	92069-059
electrical	lamps, clock 12V3W T-7	74 (Guy B. Young II)	92069-1020
electrical	lamps, dash 12V 3.4W	194, Suggest Sylvania:194LL (long life)	92069-1007
electrical	lamp, front running light/turn 32/3CP (23/8W)	1157	92069-060
electrical	lamp, rear turn signal 32CP (23W)	1156	92069-055
electrical	switch, cooling fan Also used on 1991 Honda Civic DX	ACDelco: E-1858 Auto Tune: PT2628 Beck/Arnley WorldParts: 201-0817 Beck/Arnley WorldParts: 201-1369 Borg Warner: TFS500 (Tom Masterson) Echlin (NAPA): FS-130 Facet: FS8404 (Chris Roy) Filko: TFS-1 (Bob Chappell) Four Seasons: 35934 (Bob Chappell) G.P. (?): 40-5001 Kem: TW-65 Mitech: TS-84 Motorcraft: no interchange Niehoff: WA-639B Standard: TS-84 Wells: SW504 (Guy B. Young II)	27010-1202
electrical	switch, ignition		27005-5064
electrical	turn signal flasher unit	Tridon-Stant: EP34 (Guy Young)	27002-1060
electrical	switch, kickstand (86)		27010-1214
electrical	switch, kickstand (87 up)		27010-1220
electrical	switch, neutral (gasket 92065-058)		13151-1080
electrical	wiring harness '86 (superseded by below)		26001-1773
electrical	wiring harness '87 to '91		26001-1838
electrical	wiring harness '90-93		26030-1038
electrical	wiring harness '94-up		26030-1252
electrical	wiring harness (front) 86-93		26001-1774
electrical	wiring harness (front) 94-up		26030-1285
engine	clutch nut MUST be used with the new star springs		92015-1929
engine	clutch star spring, 2 required (be sure to replace the nut at the same time)		39130-1071
engine	clutch pushrod seal	Chicago Rawhide (SKF) 3077 8mm ID, 18mm OD, 7mm wide get at any bearing supply	92049-1165
engine	counterbalancer seal	Chicago Rawhide (SKF) 7202 19mm ID, 27mm OD, 5mm wide get at any bearing supply	92049-1174
engine	filter, air	K&N: KA9084 (Rich Doell)	11013-1112
engine	filter, oil	CarQuest: 89941 (Will Perkins) Emgo: 10-37500 (Dave Mamanakis) Fram: CH6012 Hastings: LF571 (John Hinton) Honda: 15410-300-024 (Dave Mamanakis) Honda: 15410-426-010 (Dave Mamanakis) NAPA: 4941 (Dave Mamanakis) Perf-Form: J-501 (Dave Mamanakis) Purolator: ML16812 (Dale Horstman) STP: SMO-12 (Kevin Cummings) Triumph: 1210031 (Dave Mamanakis) Vesrah: SF-4004 (Doug Donner) WIX: 24941 (David Ritchie) Yamaha: 36Y-13441-00 (Dave Mamanakis)	16099-003
engine	filter, oil Flat washer that goes on top of spring (you know, the part that always gets lost) 20.5mm id X 30mm od X 1mm thk.		92022-1012
engine	gasket, engine side cover, RH		11009-1860
engine	gasket, neutral safety switch		92065-058
engine	gasket, reed valve		11009-1379
engine	gasket, pulsing cover (left side)		11060-1695
engine	gasket, valve cover		11009-1378
engine	gasket, valve cover spark plug well		11009-1377
engine	radiator hoses	From Michael Thompson NAPA hoses: NAPA #7741 (Gates 21029, 2000 Suzuki Swift Lower Hose) 1"/25.4mm ID This one gets cut into several pieces to replace the hoses at the front of the engine to the water pump. NAPA #H151 (1"/25.4mm ID bulk hose) This is a straight hose. A piece a foot long is more than enough to replace the straight hose from the thermostat housing to the filler assembly. The final hose, from the filler to the top of the radiator, I bought from a local dealer. P/N 39062-1164 Some have said that a second NAPA #7741 will work there, but I didn't like the way it looked there.
engine	radiator cap (32mm ID x 16mm deep neck) 0.9bar / 13psi Same as 1978 Ford Fiesta	Carquest :33028 (Guy B. Young II) Stant: 10227 (boxed) (Guy B. Young II) Stant: 11227 (blister pack) (Guy B. Young II) Stant: 10229 (Bryan Moody) CST: 7013 (Bryan Moody) Motorcraft: RS62 (Bryan Moody) Motorcraft: RC19 (Bryan Moody) Beck/Arnley: 133-8060 (Bryan Moody) Beck/Arnley: 133-8078 (Bryan Moody) Gates: 31527 (Bryan Moody) AC-Delco: RC19 (Bryan Moody)	49085-1053
engine	shift lever (to transmission shaft) THIS IS THE ONE THAT USUALLY BREAKS		13242-1195
engine	spark plugs, platinum	NGK: D8EVX
engine	spark plugs, standard	NGK: D8EV ACDelco: R121XLS	92070-1011
engine	spark plug cap		21160-1065
engine	thermostat Also used on 1983 Honda Accord	ACDelco: 131-17 Carquest: 31068 (Guy B. Young II) Futaba: R124 (Kevin Arnold) Mitsubishi: MB221855 (Kevin Arnold) NAPA: 142 (Guy B. Young II) Pep Boys: 29368 (Guy B. Young II) Stant: 13368 (boxed) (Guy B. Young II) Stant: 35368 (blister pack) (Guy B. Young II) Toyota: 16401-63010 (Kevin Arnold)	49054-1051
engine	thermostat o-ring 32mm OD x 25mm ID x 3 mm	McMaster-Carr (viton) PN#9263K275 $9.90 pk/10 (buna-n) PN#9262K275 $7.74 pk/50	92055-112
engine	valve cover, Europe/Canada model (does not have provision for reed valves)		14024-1082
engine	washer, head cover bolt (the cup shaped washer that the valve cover bolts go thru)		92022-1487
engine	Water Pump Rebuild Kit	K&L: 15-4343
engine	water pump oil seal	Chicago Rawhide (SKF): 4752 12mm ID x 28mm OD x 7mm wide (Mark Cipriano)	92049-1416
engine	water pump external pump o-ring, 33mm		92055-1266
engine	water pump impeller Cover o-ring		92055-1271
fuel	carb bowl o-ring		92055-1222
fuel	carb needle (float valve) clamp		16044-007
fuel	carb needle (float valve)		16030-1007
fuel	petcock to tank o-ring		51039-010
fuel	petcock lever o-ring		92055-1027
fuel	petcock assy. (complete)		51023-1130
fuel	petcock diaphagm cover		16146-1005
fuel	petcock diaphragm assy.		43028-1015
fuel	petcock diapragm o-ring		670B1504
fuel	petcock lever spring		92081-1171
tools	Microfiche ZG1000A1-A3 (covers 86-88 models)	Why buy it? Go to BuyKawasaki.com	99961-0211
tools	Hex Drive Socket (12mm 1/2" Drive) fits front axle	McMaster-Carr PN#5571A68 $9.04 ea.
tools	Hex Key (12mm Long Arm) fits front axle	McMaster-Carr PN#6958A19 $3.94 ea.
tools	Socket 27mm fits rear axle and rear drive fill plug (1/2" drive)	McMaster-Carr PN#7149A29 $7.51 ea.
tools	Wrench, spanner-steering head Metric Fixed Head Hook Style Spanner Wrench For 40-42mm Circle Dia	McMaster-Carr PN#6975A16 $11.02 ea.
tools	ABS Cement-used for repairing broken body panels	McMaster-Carr PN#74605A54 $2.16 ea. ( 8 oz) PN#74605A51 $3.56 ea. (16 oz) PN#74605A52 $5.89 ea. (32 oz)

Note #1: online bearing and seal sales atA&W Bearing or Johnson Bearing
Note #2: Be sure to check that the female sockets in the plug are TIGHT on the bulb. I have had problems with this and burnt up the NAPA plug.

ACCESSORIES
Prices are approximate, your cost may vary, shop around!

Other parts

Larry Buck
purveyor of fine Concours products
Lightbars, helmet relocation brackets, conspicuity products, racks, CB mounts

Bryan Moody
Fuel Cell Kits, Rifle windshield shelving system

Sampson Sport Touring
Fuel Cells, Luggage Racks

Givi Key Info
Givi Replacement keys are available from most lock shops. Use an ILCO X226/HYD12 blank (Dr. Squido Calamari)

Factory extended windshield	K53020-083	$209.95
Factory trim for above	53044-1196	$9.95
Factory luggage rack	K53020-083	$117.95
Factory Backrest and pad 86-93 models	K53043-052	$76.95
Factory Backrest and pad 94-present models	K53043-052A	$84.95
Factory adaptor to mount backrest and pad to luggage rack	K53021-083	$84.95
Factory saddlebag liners Black/Red	K99994-335	$65.95
Factory saddlebag Liners Black/Gray	K99994-337	$65.95
Factory Air Deflectors (similar to Baker Air Wings)	K53003-020	$69.95
Factory Fairing Extender Kit (contains both side extensions and trim)	K99996-1103	$64.95
Factory Tank Bra	K99994-918	$30.00
Jet Kit by Factory Pro	K21
Rifle Windshield system	http://www.rifle.com	$199.00 standard price
Rifle base ONLY	0.201.1116	$129.00
Rifle windshield ONLY 15" clear	0.211.0001	$70.00
Rifle windshield ONLY 17" clear	0.211.0002	$70.00
Rifle windshield ONLY 19" clear	0.211.0003	$70.00
Rifle windshield ONLY custom	0.211.0004	$95.00
Rifle windshield ONLY 15" tinted	0.211.0011	$80.00
Rifle windshield ONLY 17" tinted	0.211.0012	$80.00
Rifle windshield ONLY 19" tinted	0.211.0013	$80.00
Rifle windshield ONLY custom	0.211.0014	$105.00
Baker Air Wings-the genuine article	CONAW http://www.bakerbuilt.com/	$49.95
Race Tech Cartridge Emulators (94 up)	FEGVS3801	$139.95
BMW Type Electrical Connector (John Deere)	RE11344 PLUG AL25073 SOCKET

CLOTHING

Clothing-Lands End Turtleneck Sweaters

From David Neal, COG #32

And if you're interested in their turtlenecks:
1. These are some of the handiest, most versatile motorcycle wear I have (along with wool military sweaters in silverdammit, natch).
2. Land's end lists only 100% cotton in their catalog, but they do sell a mixture (70/30 or 60/40-I forgot). My old Land's End turtlenecks were 50/50 cotton/poly blend, and I thought the mix felt softer than the 100% cotton variety.
3. No experience with Land's End logo, but on the ones I had done in town years ago (before the logo was set up with Land's End) I noted that when on the garment, the silver thread looked gray, and the white thread looked silver. The white seemed to reflect light more, giving a silver hue to the logo. I preferred the white thread to the silver thread, as it stood out a bit more. Don't know if the same holds true for Land's End logo work, but I'll know in a week or so.
4. I ordered 'em with the old COG logo (and the words Concours Owners Group) on the neck, offset to the (wearer's) right.

If you decide you'd like to have a few of these WITH logo, you'll have to call the Land's End corporate department (800) 338-2000. The turtlenecks are $17.50 each/logo $5.30 extra. The logo number is 922906K, and don't forget to specify the thread color (no extra charge) when ordering.
David R. Neal
Danville, VA.
AMA Life Member
COG #32

Any technical information you would like to contribute? Click here!

BACK TO THE CONCOURS TECH PAGE